Leading 10 common forklift mishaps ， forklift operation ought to focus on these matters ！.

Do not take too lightly the forklift at work. If the operation is bad, there will certainly be significant crashes in mins, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's view, and the individual in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly created casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the load is secure and reputable.
4. The start needs to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal must be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to lose lateral security and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the lots have to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt way, and they will never ever operate with diseases or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks ought to be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a solitary fork or make use of a fork top or pull. In unique situations, safety and security warning signs need to be established to remind surrounding pedestrians. .
3. In the process of packing and dumping items, the forklift should be stopped with the brake. .
4. The speed of the lorry should be slow-moving and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled objects and hurt individuals. .
5. When using a fork to fork the goods, the fork should be as deep as feasible under the lots, and it needs to be noted that the fork tip should not touch other products or objects. The tons must be supported with marginal back tilt of the gantry so that the tons does not slide in reverse. The pole can be tilted ahead a little when the tons is decreased to allow for very easy positioning of the tons and removal of the forks. .
6. It is forbidden to fork items at broadband and ram difficult things with the fork head. .
7. When the Stand-on Electric Pallet Stacker forklift is functioning, it is forbidden for individuals to loaf the fork, so regarding prevent the collapse of the goods and injure individuals. .
8. Overwhelming is banned, and it is banned to use forks to lift personnel to take part in high-altitude procedures to avoid high-altitude dropping crashes. .
9. It is not enabled to use the brake inertia to slip, put, round or roll objects. .
10. It is not permitted to utilize forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Before leaving the forklift, you have to unload the goods or lower the fork framework.
2. Pull the hand Electric Forklift Truck for Warehouse brake handle to dead or depress the parking brake button.
3. The engine is shut off and the power is cut off. (Except for special conditions, such as the vehicle driver does not leave the car's line of vision and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the look ought to be inspected, and gas, lubing oil and air conditioning water must be added.
2. Examine the safety efficiency of starting, running and braking.
3. Inspect whether the lights and horn signals are complete and efficient.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are typical.
5. After the forklift is running, the exterior leakage should additionally be inspected and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the cars and truck;.
2. When you run into a person before you throughout driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning ought to not be as well sharp to avoid the tendency of " totally free turning";.
6. Running up and down the slope ought to be sluggish and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the gradient is more than 10%, the automobile must be driven backwards when declining;.
8. When the forklift personnel carry the goods and move forward, if they run into big or hefty goods and go to the chauffeur's line of vision, they must take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not allowed to lift the goods for long distance driving.
3. It is not allowed to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to get the goods.
6. It is not allowed to make use of braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring people to work with the pallet or fork, and it is purely prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, railway crossings;.
2. Sections with a longitudinal incline greater than 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844